Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, AnicaLin
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > AirGraver Networking - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 05-30-2013, 12:08 AM
elgallego elgallego is offline
Copper
 
Join Date: May 2013
Location: Orlando, fl
Posts: 6
Thumbs up Want to start air engraver

Hello every one, my name is JR Vazquez (elgallego). I star engrave in wood with a Shofu Air engraver. I want to know is my system is compatible, for used the Stainless and Damascus handles for PalmControl® AirGravers and if I need also the CarbaltXD™ Blanks. Thank you.
Reply With Quote
  #2  
Old 05-30-2013, 03:46 PM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,360
Default Re: Want to start air engraver

Hi to the forum
Well the system you have is rotary and the Lindsay airgraver is a pneumatic hammer. So the bottom line is no
Reply With Quote
  #3  
Old 05-30-2013, 07:21 PM
elgallego elgallego is offline
Copper
 
Join Date: May 2013
Location: Orlando, fl
Posts: 6
Default Re: Want to start air engraver

Dave,
Thank you so much for your welcome. I know the Shofu is a rotary system, but I have the compressor, valve and pedal that I cant connect the Palm Control AirGravers.
If I have the compressor air system I just need the Palm Control AirGravers and the graver steels?
Reply With Quote
  #4  
Old 05-31-2013, 12:10 PM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,360
Default Re: Want to start air engraver

yep a regulated compressed air source (clean and dry) hook up the palm control and go to it. the gravers are 3/32 square I use the carbalt and HHS. the sharpening system will save a lot of headache simple to use and a perfect point every time and you will be doing a lot of sharpening
Reply With Quote
  #5  
Old 05-31-2013, 06:53 PM
elgallego elgallego is offline
Copper
 
Join Date: May 2013
Location: Orlando, fl
Posts: 6
Default Re: Want to start air engraver

Dave,
Thanks for your great help.
Reply With Quote
  #6  
Old 05-31-2013, 08:21 PM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,360
Default Re: Want to start air engraver

Of I remember right Steve supplies a pre ground graver. Don't use it keep it as a reference
Reply With Quote
  #7  
Old 05-31-2013, 10:57 PM
elgallego elgallego is offline
Copper
 
Join Date: May 2013
Location: Orlando, fl
Posts: 6
Default Re: Want to start air engraver

OK, Thank you
Reply With Quote
  #8  
Old 06-03-2013, 11:36 AM
dlilazteca dlilazteca is offline
Gold
 
Join Date: May 2013
Location: texas
Posts: 138
Default Re: Want to start air engraver

check for my youtube video my user name is carlos delao i have a video of a lindsay classic unboxing...I also own a shofu both are different systems but you do use the same compressor
Reply With Quote
  #9  
Old 07-03-2013, 07:50 PM
gmgunsmith gmgunsmith is offline
Copper
 
Join Date: May 2013
Location: Carrollton, TX
Posts: 2
Default Re: Want to start air engraver

A good 3/4 HP 4 gallon air compressor is suitable to run a combination of pneumatic systems.

As you can see in this picture I have both a 400,000 RPM rotary and a Lindsay AirGraver, each with its own regulator ganged together to support the different air pressures needed.



All of the air fittings, hoses, and regulators are available at most well equipped hardware stores such as harbor Freight, ACE, etc. I didn't find any reasonably priced regulators at Home Deport or Loews. Both Home Deport and Loews have a good assortment of small diameter pressure hose.



Here's the restoration project for an old shotgun that will be engraved later.

Last edited by gmgunsmith; 07-03-2013 at 08:08 PM. Reason: add info
Reply With Quote
  #10  
Old 07-04-2013, 06:00 AM
hobochief hobochief is offline
Gold
 
Join Date: Sep 2010
Location: Florida
Posts: 140
Default Re: Want to start air engraver

You are in luck as at the Orange County Convention Center there will be both the Classic and Palm Control up and running THurs Fri and Sat next weekend. FUN SHOW www.funtopics.com will give you directions and come to the HOBO NICKEL Table and use the tools all day. WE will have optivisor's and microscopes and gravers and sharpening systems available to use and Lindsay Brochures to place your order from. Please join us just ask for the HOBO TABLE somewhere in the 300-400 table numbers.
Reply With Quote
Reply

Bookmarks


Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 05:32 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.